Triple Mirror Passive Sensor TAKEX PIR-T15WE
- Triple Mirror Optical System: The unique combination of triple mirrors and three twin pyros enable 4 selectable operation modes including low position, high position, pet, and high density; for distances up to 49’ (15m) from a mounting height of 6.6’ (2m) to 20’ (6m), throughout a full 80°.
- Optimised Detection Area: The triple mirror optical system features a geared mirror array allowing detection patterns to be dynamically optimised for maximum performance depending on the chosen mounting height and operation mode.
- Pet Immunity: Independently controlled pyro devices in each optical unit use intelligent signal processing to eliminate nuisance alarms from small animals, and a dedicated pet operation mode further enhances discrimination performance against medium-sized animals.
- Precise Area Adjustment: Precise detection area adjustment is made possible by projecting coloured LED’s onto the surface of each mirror -visible only from inside the detection zone during the alignment process allowing sensitive zones to be fine-tuned to individual site requirements as desired. Unnecessary areas can be cancelled using the supplied area-masking sheet.
- Design Conscious: The PIR-T15WE’s unassuming design allows it to blend discreetly into any industrial, commercial or domestic environment, and the internally adjustable optic system helps to conceal the detection area and direction for more secure protection.
- Other Functions: Enhanced features including creep zone detection, near area cancellation, dual outputs, and lightning surge protection make the PIR-T15WE a key addition to the TAKEX family of high performance intrusion detection sensors.
Specification
| Model | TRIPLE MIRROR PASSIVE SENSOR |
| Model number | PIR-T15WE |
| Detection system | Passive infrared |
| Detection area | Wide angle (80°) detection Detection distance: 49’(15m), 108 rays (54 pairs) |
| Power supply | 9 to 28V DC (non-polarity) |
| Current consumption | Max. 40mA |
| Alarm output | - Contact method: Dry semi-conductor contact, N.C./N.O. selectable - Contact operation + One-shot operation when detecting intrusion + Continuous output in the event of cover monitor error + Continuous output in the event of alignment position error + Continuous output in the event of self diagnosis error + Continuous output in the event of power voltage error + Continuous output in the event of long-term diagnosis error - Contact rating + 24V (AC/DC) 0.25A (resistive load) (built-in contact protective resistor 3.3Ω) |
| External output | - Contact method: Dry semi-conductor contact N.O. - Contact operation: One-shot operation/Off delay operation selectable when detecting intrusion - Contact rating: 24V (AC/DC) 0.25A (resistive load) (built-in contact protective resistor 3.3Ω) |
| Tamper output | - Contact method: Dry mechanical contact, N.C. - Contact operation: Continuous output - Contact rating: 24V (AC/DC) 0.1A (resistive load) (built-in contact protective resistor 3.3Ω) |
| Alarm LED | Red LED: - Blinks* during warm up - Lights up* when detecting intrusion - Continuously blinks in the event of cover monitor error - Continuously lit in the event of alignment position error - Continuously blinks in the event of self diagnosis error - Continuously lit in the event of power voltage error - Continuously blinks in the event of long-term diagnosis error (*ON/OFF selectable using the mode selector) |
| Memory LED | -Red LED: Blinks for 3 minutes during memory display, Auto reset operation either of continuous lighting for 47 minutes or blinking for 50 minutes selectable (Blinks to lights/blinks, ON/OFF selectable using the mode selector) |
| Functions | Sensitivity selection, Operation mode selection, Alarm memory LED, Selfdiagnosis, Low voltage monitoring, Temperature compensation,Tamper,LED area checker, Environmental adjustment ,Creep zone detection,Walk test mode, Near area cancellation, Long-term diagnosis |
| Mounting positions | 6.6ʼ to 20ʼ(2.0 to 6.0m) (varies depending on the operation mode) + Low position mode : 6.6ʼ to 9ʼ(2.0 to 2.7m) + High position mode : 9ʼ to 11.5ʼ(2.7 to 3.5m) + Pet mode : 8.3ʼ to 10ʼ(2.5 to 3.0m) + High density mode : 6.6ʼ to 20ʼ(2.0 to 6.0m) |
| Area angle adjustment range | Horizontal direction : 90° (by 5°pitch) Vertical direction : 17° (no stage adjustment) |
| Ambient temperature range | 25～+55℃(no condensation and freezing) |
| Installation place | Indoor/outdoor wall surface: Can be mounted on poles and ceilings (or under eaves) using optional accessories |
| IP rating | IP55 |
| Connections | Terminals (M2.6 self up terminal) |
| Weight | Approx. 600g |
| Appearance | Body: ASA resin (gray), Window: PE resin (white) |
- Bảo hành: 12 tháng.
m.jpg "Báo động TAKEX | Pole cover TAKEX BP-100MW(SET)")
